DURRIDGE offers a variety of accessories for the RAD8 and RAD7 radon detectors. Each is explained in detail below.
Range Extender – Increase the range of the RAD8 and RAD7 in high radon areas
Multi-Gas Sampling Data Logger – Measure CO2 and other gasses in the air entering the RAD8 or RAD7
Cool Trap – Remove moisture from air entering the DRYSTIK, RAD8, and RAD7
Indoor Faucet Connector – Adaptor for taking tap water samples
Relay Box – Accessory for issuing alerts and controlling the RAD7 operating environment
Serial to Bluetooth Adaptor – Adaptor for communicating wirelessly with the RAD7 from a computer
USB to Serial Adaptor Cable – Cable for connecting the RAD7 to a computer
Water Switch – Prevent water from entering the DRYSTIK and other sensitive devices
Range Extender
Increase the range of the RAD8 and RAD7 in high radon areas
The Range Extender mixes fresh air with sample air to reduce the concentration of radon in the air fed to the RAD8 and RAD7 radon detectors by an order of a magnitude, greatly increasing its effective range.
The extender consists of two parallel capillary tubes joined at one end to the outlet hose connector. Fresh air is fed to the input of one tube while the incident radon sample is fed to the other. A differential pressure sensor across the two tube inputs, with a needle valve for adjustment, is used to ensure that both capillary tubes have the same pressure drop across them.
With this system the radon concentration delivered to the RAD8 or RAD7 will be reduced by a factor of 10:1 regardless of the strength and flow velocity of the instrument’s pump. The pump can cycle on and off without affecting the reduction factor.
The Range Extender can be used for the measurement of very high radon concentrations in air, in soil gas and in water. It can also be used with any other instrument that has its own pump, for any gas. If used to extend the range of thoron measurement care must be taken to assess and correct for the additional decay of the thoron due to sample acquisition delay.
Physical Specifications
| Range Extender Shipping Dimensions | 12″ x 12″ x 10″ (30 cm x 30 cm x 25 cm) |
| Range Extender Shipping Weight | 4 pounds (1.8 kg) |
$1,534.00Add to cart
Multi-Gas Sampling Data Logger
Measure CO2 and other gasses in the air entering the RAD8 or RAD7
The portable Multi-Gas Sampling Data Logger is designed to log CO2, CO, O2, and CH4 in the air being fed through a RAD8 or RAD7. It also measures air temperature and relative humidity. The device works at elevated ambient temperatures and relative humidity levels.
The instrument runs on battery power, and it stores readings internally with a time stamp. The data is retrieved from the unit via a USB connection to a computer.
The Multi-Gas Sampling Data Logger is offered in six models, for measuring CO2 concentrations of up to 1%, 5%, 10%, 20%, 30%, and 100%, respectively. All models include a data cable for retrieving accumulated measurements. A programmable backlit LCD changes color according to CO2 levels. The package includes filters, fittings, tubing, and an auxiliary international power supply.
A CO2 Sampling Data Logger is also available, for customers who do not need to measure CH4, O2, or CO.
Technology
Items marked with an asterisk (*) pertain to the Multi-Gas Sampling Data Logger only.
- CO2 sensing method: NDIR (Non-dispersive infrared)
- CO2 measurement ranges: 1%, 5%, 10%, 20%, 30%, and 100%
- CH4 sensing method: Electrochemical sensing*
- CH4 measurement range: 5%*
- O2 sensing method: Oxygen quenching*
- O2 measurement range: 0-25%*
- CO sensing method: Electrochemical sensing*
- CO measurement range: 0-5,000 ppm*
Specifications
- Temperature measurement range: 0-50°C ± 1°C
- RH measurement range: 0-100%, ±3% @25°C (20-80%RH), others ±5%
- Barometric pressure measurement range: 50-110 kPa, ±0.4 kPa*
- Sampling input method: Tube sampling (1/8″ ID)
- Data storage medium: 16 GB SD Card
- Measurement interval: 15 second to 18 hours.
- Calibration certificate included
- No maintenance required
- Dimensions: 9x4x2 in (226x100x55 mm)
- Weight: 480g (1.05 lbs.) without batteries
Display
- LED displays CO2 and other readings in parts per million (PPM) or percentage
Power Supply
- (3) BRC 3.7V 18650 rechargeable li-ion batteries (30+ hours per charge)
Included Accessories
- 1.5M USB cable
- 16 GB SD Card
- 1/8-inch tubing (10 feet)
- International wall mount power supply
- Moisture trap
- Particulate and hydrophobic filters
| CO2 Sampling Data Logger Measures CO2 only |
$2,674.00Add to cart |
| Multi-Gas Sampling Data Logger Measures CO2, CH4, O2, and CO |
Contact us |
Cool Trap
Remove moisture from air entering the DRYSTIK, RAD8, and RAD7
The Cool Trap is an accessory that operates under pressure in a vessel of icy water, directing air through a coil of copper tubing. This process creates condensation and removes excess moisture from the air. The Cool Trap operates upstream of the laboratory drying unit, DRYSTIK, RAD8, or RAD7, to reduce the amount of moisture advancing through each.
Two versions of the Cool Trap are available: the Bucket-Sized Cool Trap and the Mug-Sized Cool Trap. The Mug-Sized Cool Trap is more portable, while the Bucket-Sized Cool Trap offers greater moisture removal due to its longer tubing. Both versions of the Cool Trap have one air inlet tube and two outlet tubes, one for outputting the dried air, and another for draining the condensed water.
Cool Trap Specifications
| Mug Sized Cool Trap | Bucket-Sized Cool Trap | |
|---|---|---|
| Diameter | 2.75 in (7.0 cm) | 7.50 in (19.1 cm) |
| Height | 5.75 in (14.6 cm) | 11.75 in (29.9 cm) |
| Weight | 0.6 lbs (270 g) | 3.2 lbs (1.5 kg) |
| Material | Copper | Copper |
$230.00Add to cart |
$348.00Add to cart |
Mug-Sized Cool Trap
DRYSTIK Configuration with Cool Trap Diagram
Cool Trap in Mug
Bucket Sized Cool Trap
Documentation
Cool Trap Configuration with DRYSTIK (PDF)
DRYSTIK Manual (PDF)
See Section 2.4, High Humidity Conditions
Indoor Faucet Connector
Adaptor for taking tap water samples
For filling RAD H2O vials or bottles, and feeding tap water into the RAD AQUA spray chamber, DURRIDGE offers an Indoor Faucet Connector manufactured by Claber Inc. and customized for use with an included length of 3/16 in (0.48 cm) ID tubing. It attaches to any indoor straight neck faucet up to 1¼ inch wide and up to 1¼ inch deep. A rubber seal clamps onto the faucet to prevent leaking or spraying, and a convenient quick-click coupler allows for fast and easy hose removal.
Connector Specifications
| Construction | UV-stabilized ABS Plastic |
| Maximum Water Temperature | 104° F (40° C) |
| Operating Pressure | 14.5 PSI (1 Bar) to 58 PSI (4 Bar) |
| Leak Pressure | 145 PSI (10 Bar) |
| Included Tubing | 20 in (50.8 cm) of 3/16 in (0.48 cm) ID tubing |
| Maximum Faucet Width | 1¼ in (3.18 cm) |
| Maximum Faucet Depth | 1¼ in (3.18 cm) |
| Indoor Faucet Connector | $60.00Add to cart |
Indoor Faucet Connector
Indoor Faucet Connector in use
Relay Box
RAD7 accessory for issuing alerts and controlling the RAD7 operating environment
At the end of each cycle the RAD7 can compare the measured radon concentration with each of two user-specified relay thresholds. If the radon level is higher than a particular amount, the RAD7 sets a relay. If it is lower, the relay is reset.
Relays can be used to electronically trigger a warning mechanism at the lower threshold, and an alarm at the higher threshold. Relays can also be used to control ventilation equipment, or to change the concentration of radon in a sealed chamber, without the necessity of a computer.
The DURRIDGE Relay Box facilitates this communication with external instruments.
Physical Specifications
| Relay Box Device Dimensions | 4.6″ x 2.4″ x 1.3″ (11.7 x 6.1 x 3.3 cm) |
Purchase the Relay Box |
|
| Relay Box | Currently Unavailable |
3-Way Serial Adaptor CableThe RAD7 3-Way Serial Adapter Cable is used to connect a RAD7 to a Relay Box and a computer simultaneously. This makes it possible to monitor a RAD7 using Durridge Capture software on the computer while the Relay Box activates alarms in response to elevated radon concentrations. |
|
| RAD7 3-Way Serial Adaptor Cable | Currently Unavailable |
DURRIDGE Relay Box
RAD7 3-Way Serial Adaptor Cable
Documentation and Diagram
Triggering Actions Based On RAD7 Measurements (PDF)
DURRIDGE RAD7 with Relay Box and 3-Way Serial Adaptor Cable Diagram
Serial to Bluetooth Adaptor
Adaptor for communicating wirelessly with the RAD7 from a computer
DURRIDGE offers an optional Serial to Bluetooth adaptor to facilitate the transmission of radon data between the RAD7 and a Bluetooth-enabled Macintosh or Windows computer running DURRIDGE’s CAPTURE software. With the Bluetooth Adaptor, it becomes faster and more convenient to perform graphing and real-time data analysis. The adaptor has been tested across distances exceeding 40 meters, through walls and trees, and it is known to support 100 meter communication along uninterrupted lines of sight.
The Serial to Bluetooth Adaptor may be powered by either an included AC adaptor or an optional 3.7V lithium ion battery, which is rated for 16 hours of continuous use. The included stub antenna may be replaced with an optional 2 dBi Dipole Antenna for an extended communication range.
The Serial to Bluetooth Adaptor comes preconfigured for use with the RAD7. Printed documentation is included, explaining how to connect and reconfigure the adaptor.
Serial to Bluetooth Adaptor Specifications
| Product ID | Parani-SD1000 |
| Communications Protocol | Bluetooth v2.0 + EDR |
| Power | 5~12VDC via standard AC adaptor or optional 3.7V 900 mAh battery with 16 hour capacity and 5 hour charge time. |
| Dimensions | 76 x 31 x 16 mm without battery pack 76 x 31 x 31 mm with battery pack |
| Weight | 24 g without battery pack 42 g with battery pack |
| Warranty | 3-year Limited Warranty |
Purchase the Serial to Bluetooth Adaptor |
|
| Serial to Bluetooth Adaptor | $199.00Add to cart |
|---|---|
Optional Accessories for the Serial to Bluetooth Adaptor |
|
| Lithium Rechargeable 16 Hour Battery | $61.00Add to cart |
| Extended Range 3 dBi Dipole Antenna | $13.00Add to cart |
Serial to Bluetooth Adaptor
Documentation
RAD7 Software
USB to Serial Adaptor Cable
Adaptor cable for connecting the RAD7 to a Computer
Durridge offers the StarTech USB to Serial Adaptor cable for connecting the RAD7 to your computer. This makes it possible to download, analyze, and export radon data using DURRIDGE’s CAPTURE software for Windows and macOS. It is also possible to issue RAD7 commands and control the RAD7 remotely.
This adaptor cable is included with all newly purchased RAD7s, and it is also available separately.
Adaptor Cable Specifications
| Hardware Chipset | FTDI – FT232RL |
| Serial Protocol | RS232 |
| Connector Types | 1 – DB-9 (9 Pin; D-Sub) Female 1 – USB A (4 pin) Male |
| OS Compatibility | Windows XP/Vista/7/8/10 Mac OS 10.X |
| Cable Length | 5 ft 11in (1.8m) |
| Power Source | USB Bus Powered |
| Shipping Weight | 0.5 lb (0.2 kg) |
| Product Warranty | 2 Years |
| Included in Package | USB to Serial Adaptor Cable Driver CD Instruction Manual |
| USB to Serial Adaptor Cable | $59.00Add to cart |
StarTech USB to Serial Adaptor Cable
StarTech USB to Serial Adaptor Pack
Related Software
CAPTURE (HTML)
Download Serial to USB Adaptor drivers
Software Drivers (HTML)
Water Switch
Prevent water from entering the DRYSTIK and other sensitive devices
The Water Switch is a device which cuts off power to a device should water enter the switch. It is specifically designed for the DRYSTIK. The Water Switch consists of a reed switch surrounded by a float that contains a magnet. If the float rises it will turn off the switch, cutting power to the DRYSTIK’s pump and preventing water from entering the device and saturing its sensitive NAFION tubing.
| Water Switch | $135.00Add to cart |
